Skip to content
Skip to content
i love sport, more and more

i love sport, more and more

  • Home
  • About
  • Contact
  • Privacy Policy
  • Terms and Conditions
← How To Hide Speaker Wires For Surround Sound
How to clip in spd pedals? →
-->

How to clean a skateboard deck?

Posted on April 11, 2022 by Eddie Ramos

Skateboards and Decks Cleaning

Dirt or mud on your skateboard deck may reduce resistance and make it difficult to do tricks. Basically, a filthy skateboard may spoil your game. It’s possible that muddy feet might cause the grip tape to slip. Dirty skateboards perform poorly. You can’t alter your performance if you don’t know how to clean your board.

Don’t worry, I’ll show you the finest DIY and home cures for cleaning your skateboard and decks. So, don’t worry about enhancing performance or keeping your skateboard clean, and save money.

Deck Cleaning using Soft Brush Wire:

This is the simplest method of cleaning your skateboard deck. You will save money and get a clean skateboard deck. This requires a soft wire brush and a Grip gum.

Step 1: Get a Soft Wire Brush

The soft wire brush may be purchased locally, but be aware that the bristles will not shred the grip tape. The brush’s bristles must be short to clean your deck’s grip tape precisely. Buying huge bristle brushes can ruin your skateboard deck’s grip tape.

Step 2: Brush the Grip Tape

Start brushing the grip’s tap using the wire brush after purchasing the soft brush. This must be done from one end of the deck to the other, section by section. This method cleans deep dirt from the deck’s surface. Also, sweep it with your hands. But careful not to force the brush or it may rip. Also, avoid stripping your board’s grit.

Step 3: Grip Gum Excess Dirt

You may get the grip gum for skateboards at a local skate store. After cleaning with the soft wire brush, apply this grip gum to clean the deck. Rub it with grip tape, then gently brush it. Reverse the procedure to receive a fresh deck. Brushing the deck gently is advised.

Cleaning your Skateboard Deck with Some Common Materials that You Find In Your Home:

If you don’t want to spend money on deck cleaning, I believe this is the best method to accomplish it.

This technique requires a firm toothbrush/soft wire brush, water, soap, grip gum (optional), bowl, and dry towel.

Step 1: Gather All Project Materials

You can quickly clean your skateboard deck or grip tape using the aforementioned items. Find an old toothbrush, a soft wire brush, soap, gum, a dry and clean towel, and water in the garage. If you have all the supplies available, you may start cleaning.

Step 2: Fill the Bowl with a Mixture of Soap and Water

Fill a medium-sized bowl with tap water and soap. Remember not to immerse your skateboard deck in water. It will destroy the skateboard’s snap or pop. You may also add lemon juice for a fresh scent, although it is optional.

Step 3: Dip And Scrub

It would help if you began cleaning at the end. Some dirtier sections need more time to remove. If your brush becomes filthy when washing the deck, rinse it back into the cleaning solution bowl and then clean the deck again. Like I stated earlier, don’t let the board touch water for too long. Also, cleaning too hard can damage the grip tap.

Step 4: Dry it with a Dry Cloth

Dry your deck after washing it with the cleaning solution and a brush. Your deck will benefit from a microfiber cloth. Place the towel over the deck and pat it dry. Fold and press the towel again until the deck dries. The wood and the bottom will also dry. Using paper towels for drying can generate more bulk and breakage.

Step 5: Drying Time

First, dry the board for 3 hours in an open place. After washing, let the board dry completely before riding it if it is safe for your skateboard.

Step 6: Clean Up Excess Dirt Grip Gum

If you have grip gum, you may rub it over the board; this is optional. Grip gum is pricey, so use a cheap rubber cement eraser instead. It’s near the hardware shop and works.

Dirty skateboards reduce performance intensity. If you want your skateboard to perform as it used to, follow the procedures below.

 

Clean Skateboard Bearing

You can do it all outside your house. If your bearing becomes filthy, you’ll need lubrication, a towel, single-use cups, and speed cream. To maximize cleaning efficiency, roll the bearing before cleaning and run it after cleaning. Added baring and removal shields. Place the towel on the work area to avoid lube-related injuries. 

 

For doing this cleaning process, you have to do the following things:

Pour or spray the lubricant into a cup first. Then pour the bearing into the cup and let it settle in the lubrication. They can be kept for an hour. If the lubricant in the cup becomes dirty, replace it with a new pure. Repeat for your eight bearings. Rep until you observe a clean and fresh bearing into the cup. Now it’s time to wipe it with the paper towel. Don’t mix them together; clean one after the other for best results. Shake the bearing to remove the excess. Finally, apply speed cream with Teflon to finish them up.

SKATEBOARD WHEELS CLEANING

Your wheels will eventually become filthy. When the wheels get yellow, you know they need cleaning. You may edit it but not reuse it. You can clean it with a moist cloth, but it doesn’t work better.

Remove the wheels first using a wrench. I need to clean the bearings. Separate them using a screwdriver. Then clean them carefully with a toothbrush or wire brush and dish soap. Brushes with narrow bristles can swiftly clean within curves and edges. Then soak them in warm water for 15-20 minutes and scrub them. Lotion helps the wheels move better. Finally, dry them with a paper towel.

SKATEBOARD GRIP TAPE CLEANING

This DIY method allows you to bike again without buying new grip tape. This requires microfiber cloths, a ribber, and a soft brush. You need enough pressure to cleanly glide it across the deck. You may use a soft dry brush and then a soft towel to remove the dust. Using a damp one and cleaning it with water may harm and degrade the grip tape. To clean the grip tap, use a soft brist

Another way to clean grip tape exists. Clean the windows with the window cleaner and delicate brushes. Repeated strokes may clean your skateboard’s grip tape till you reach the other side. Then dry it with the microfiber towels. Then use the grip gum technique to clean completely. It only works on dry grip tape, not moist grip tape.

SKATER TRUCK CLEANING TIPS

Clean the skateboard trucks with white vinegar and a paper towel. After removing the skateboard’s trucks, you can see the rust. Rust may cause truck breakdown. Wipe vinegar on the dust and rust to remove it. After a few hours, clean and massage it, then dry it with a paper towel. Spray lubricant on them to stop corrosion.

So, I hope you learned a lot about cleaning your skateboard from this post. All the approaches are simple and will assist you a lot. But remember, don’t use DIY methods unless you’ve done them right. 

 

This entry was posted in My Blog. Bookmark the <a href="https://footballcowboysproshop.com/how-to-clean-a-skateboard-deck/" title="Permalink to How to clean a skateboard deck?" rel="bookmark">permalink</a>.
← How To Hide Speaker Wires For Surround Sound
How to clip in spd pedals? →

Comments are closed.

© 2022 | Blog info WordPress Theme | By Bharat Kambariya

Terms and Conditions - Privacy Policy