How to change lawn mower oil

The small engines that power lawn mowers require oil changes in the same way that automobile engines do. The oil in most lawn mower engines should be changed every 20-50 hours of operation.
The owner’s manual for a lawn mower will specify how frequently the mower’s oil should be changed. An oil change should be performed at the very least once a year, in conjunction with other seasonal tune-up maintenance.
This article will walk you through the process of changing the oil in most lawn mowers. Changing mower oil is a simple process that can be completed in as little as five minutes.

Red Lawn Mower getting some maintenance

Step 1: Prepare for the Oil Change

There are a few things to do before removing the old oil from the mower.

1. Warm up the engine

In order to speed up the oil change process, it’s a good idea to let the mower engine warm up first. As a bonus, it will be a lot easier to get rid of all of the old oil.

2. Clean around the oil fill area.

Clean the oil fill area with an air compressor or a dry towel.

3. Prepare an oil pan to catch the oil.

You’ll need an oil pan or something similar to catch the oil that comes out of the lawn mower. Placing the pan on the side of the mower that will be tipped over to drain the oil will be most effective.

Step 2: Dump the Old Oil

The mower is now ready for its oil to be drained, thanks to the preparation work that has been completed.
4. Remove the oil fill cap.

5. Tip the lawn mower on its side to drain its oil.

If you have the opportunity, turn the mower on its side for about a minute to allow the old oil to drain out completely before continuing.

 

Step 3: Replace the Oil Filter (if Applicable)

However, while the vast majority of walk-behind lawn mowers do not have oil filters, there are a few models available that have them built into the engine design. If your mower model has an oil filter, we’ve included the steps for changing it below in case yours does as well.
To complete your oil change, skip ahead to Step 10 if your lawn mower engine model does not include an oil filter.

6. Prepare something to catch the oil.

If you remove the oil filter from your lawn mower, you risk spilling the oil it contains.
Find a small container that can fit under the filter as you unscrew it to catch the oil.

7. Unscrew the old filter.

The old filter simply unscrews.

8. Coat the seal of the new filter with oil.

Before installing the new oil filter, it is necessary to coat the seal with oil to ensure that it is properly sealed.
Apply a thin layer of motor oil to the outside lip of the new filter with your finger. Remove the old filter and discard it. The application of a thin coat of oil will ensure that it seals tightly once it is in place.

9. Install the new oil filter.
As you screw in the new oil filter, make sure it touches the plate that it is supposed to seal against. After that, tighten the filter by turning it a quarter or half turn.

Step 4: Refill Mower Oil

This means that the mower is now ready for its engine oil to be replaced. Recall that overloading the oil in a lawn mower engine can be just as detrimental as under-fuelling the engine.
Consult the mower’s owner’s manual to determine the exact amount of oil that the mower requires.
The dipstick on the mower should be the final arbiter when determining the proper oil level. The majority of mowers require between 2/3 and 3/4 of a quart of oil.

10. Add engine oil gradually until it is full.

Check the oil level with the dipstick a few times while you’re filling it.
The risk of overfilling is reduced by creeping up on the “full” line like this.

11. Replace oil cap.

Your lawn mower oil change is now complete.

Conclusion

Changing the oil in your lawn mower’s engine will help it run more powerfully and consistently. This, along with other simple equipment maintenance procedures, will significantly increase the life of your tools.

See more : Best lawn mower with bagger

<span class="entry-utility-prep entry-utility-prep-cat-links">Posted in</span> My Blog | Comments Off on How to change lawn mower oil

How to do finger skateboard tricks?

Besides rails, ramps, and other types of obstacles that you can use with your fingerboards, Tech Deck also has some great ones. You can use them to have a lot of fun. However, if you don’t have a lot of money, these things aren’t very important because you can use pencils, staplers, books, and binders instead. You can use this to grind, slide, or even do an ollie.

 

Choose a trick that you want to learn. You start by putting your index finger in the middle of the fingerboard. Then, put your middle finger on the back of the board.

Use your middle finger to shove it in your direction. Do a light flip towards you. Turn the board around and put pressure on your index finger to control it.

Tricks for the keyboard

 

Tricks to flatten and flip your fingers on the finger board

Ollie

You should slap the tail back with your middle or ring finger (goofie) and it should pop up. Slide your index finger to the nose while you are in the air to level this out. This may not work at first. If this is the case, try to go back first to finish this trick.

 

Fakie Ollie is a fan of the show.

When you do the fakie ollie, you don’t level out the board. Instead, you go back in the direction the tail is going. It might be necessary to scrape off the grip tape with a razorblade to make it sticky for this trick to work. The Fingers of Fury video shows one of the guys with his board like that.

Nollie

If you hit the tail of the skate, you do an ollie. If you hit the nose, you go from there.

Fakai Nollie is the name of the person who wrote this.

The same as the fakie ollie, except you’re going forward and you push down with your nose. If you can’t do the fakie ollie, look at the note above that talks about that move.

900

When you do this, the board spins around 2 1/2 times around. You have to push much more hard on the tail, so the board spins around 180 degrees (5 if in increments of 180 turns). Works best when there is a lot of air. It can be learned on flat land.

#Ollie North is in the north of the country.

An ollie is the first thing you should do when you start. Then, twist your hand to the left so that the board is level. Then, make sure you land well. This can be tricky.

OLLIE IS VERY COOL.

Take off the board when it has done a full kickflip and land on your nose. It is hard at first, but don’t give up. Keep going and keep going.

Impossible

It looks like you’re doing an ollie. Instead of keeping the board on your fingers as in the example above, let it flip over one finger like a flip and land on the ground with your finger in the middle (nose over tail). If you use your pinky, someone has called it “pinky impossible.”

Almost the same as its cousin the impossible, except you use your ring finger to go backwards sideways with the board. Wait for the board to come back around your finger and turn 360 degrees. Take hold of the board with your pointer finger, then turn the board upright and land it on the ground.

Shove-it

Afterwards, pull your middle finger or ring towards you in an ollie (like the one shown above). This is how it should work: Before you land, the board should turn 180 degrees with its wheels down.

360 Toss-it

If you want to make this game a little different, you turn the board 360 degrees instead of 180 degrees. You can try this trick with a 540, 720, and maybe even a bigger number. A note: You might have to do a really high ollie in order to get some of the higher turn shove-its that you want.

Fakie

With your middle or ring (goofie) on the side you are going, you ride the board backward.

A lot of people have changed their sex.

To do the sex change, start with a kick-flip and twist your hand so you move your fingers.

Had to Flip

Push the back of the board down with your middle (normal) or ring finger to do a hard flip (after executing the ollie). Before the board is level with the ground, do a half heelflip. This is for all of you who own tony hawk. You can find it in the trick tutorials section. Heel and backflip in one: It’s like half of both of these moves put together.

Double Back

Another way to do a hardflip is to do a hardflip two times.

Pressure Flip is the name of the game.

It’s like the hardflip and the ollie. An ollie, but when you’re leveling it out, kick the tail down to make it spin like a hardflip, then land it the same way.

wheela

There is only one wheel on a 1 wheela.

Manual

When you push down on the front or back of the board, the board should now only be on one truck. For a frontside, go in the direction of the tail or nose, and for a backslide, go the other way.

Kickflip

Then, raise the board. There are ways to start it off. A little less than 90 degrees to the ground, then spin the board by pulling your index finger toward you and land it. This is how you do it.

Varial kicked off with a flip.

A hybrid of a pop shove it and a kickflip. You start with a shove it, but then pull your fingers in to get the kickflip part in, like you see above. Watch the board as it flips and turns, and wait until it reaches the point where you started out, grip tape up, before you start riding. In order to get the timing down for this trick, it may take a while.

Heelflip

Do the same thing as the kickflip, but instead of pulling your pointer finger toward you, kick it out by putting the nail of your pointer finger against the edge of the board closest to you and pushing out so the board spins away from you. This is a cousin of the kickflip.

Varial, flip your head

When you do a varial kick flip, you shove it and then flick out to get into the heelflip. Now land it with grip tape up.

Vert

This trick needs a smooth, vertical surface. Make your way up on it and go back and forth with the fingerboard facing the ground.

Board Twist

To do this trick, start with an ollie or get some crazy air off of a ramp. Twist the board a little one way, then twist it back and land it.

 

Conclusion

Will finder skateboarding stay as popular as it is now? It’s not clear. Skaters like me, who go to skate parks as often as possible and finger skate every night, are more likely to be into it.

If you haven’t tried it, I think you should.

Other posts:

HOW TO USE AN ESPRESSO MAKER?

How to clip in spd pedals?

<span class="entry-utility-prep entry-utility-prep-cat-links">Posted in</span> My Blog | Comments Off on How to do finger skateboard tricks?

HOW TO USE AN ESPRESSO MAKER?

ESPRESSO MAKER, THINGS NEED TO KNOW!

People and businesses frequently fantasize of owning an espresso machine; the aroma of freshly brewed coffee, the intensity of the flavor, it’s really something special. Throughout today, we’ll cover all there is to know about espresso machines, including the proper way to utilize them.

What is a Espresso Maker, exactly?

A machine that makes coffee by pushing pressured water through a disc of ground coffee and a filter, creating espresso, is known as an espresso maker.

What is the procedure?

Espresso machines are now used by millions of people to brew their coffee each day. Many individuals, on the other hand, are completely unaware of what this equipment performs or how it is constructed. The following are the major components of an espresso machine:

Water and Pumping Station

No matter what type of espresso machine you have, it will have a water tank. According to the size of the machine and the frequency with which it is used, water may be drawn from a deposit or a distribution network. Clean water with a low mineral concentration is often necessary for this equipment to function properly.

Boiler

The boiler is the second most significant component of an espresso machine. It is responsible for heating the water that passes through the machine. It is possible to find computers that contain a two-heater system, although the configuration differs from one to another.

Group Head

The group head is the point at which water and coffee come together. How Does It Work? It’s the last stage in the brewing process that results in the cup of coffee you’ll enjoy later.

Espresso machines are now a wonderful tool for brewing tasty, high-quality coffee at home or on the go. Although the procedure varies from brand to brand, the following is the general procedure for operating an espresso maker:

Preparing to Fill the Water Tank

Water should be added to the tank as soon as possible. Water tanks are often labeled with visible level marks to allow for brewing varying quantities of coffee.

When you’ve finished filling the tank, switch the machine on to begin working. It is critical to wait until the machine has completely turned on before beginning to brew.

Remove the Porta-Filter from the system

Remove the porta-filter while the machine is still running. The circular filter is housed inside the porta-filter housing. Filters are available in a variety of sizes, including basic and double. Place the filter in the porta-filter and close the lid.

Preparing to Fill the Filter with Coffee

It is now necessary to place the ground coffee in the filter. Fill it evenly using a spoon to make it easier to do so.

Keeping the Coffee Under Control

Tampers are used to push down the ground coffee, compressing it, and enhancing the flavor of the coffee by increasing its concentration.

Preventing the Filter from working

The porta-filter should be locked into the group head.

Place your Cup at a strategic location.

You should place your cup exactly under the coffee spout so that you may get the coffee immediately. Make certain that the container’s size is appropriate for the quantity of coffee you’re making.

Begin the brewing process.

Start the espresso machine to prepare your shot of espresso. Within minutes, you’ll be sipping on the excellent coffee you’ve been craving. What are the benefits of using an espresso maker?

There are a variety of factors that have influenced individuals all around the globe to purchase an espresso machine. Here are some of the most common reasons why individuals opt to do so:

Because it is a rapid brewing technique, it enables you to learn more about coffee while still tasting delicious. It also allows you to explore the huge universe of brewing. It is environmentally friendly.

Please find more information here.

<span class="entry-utility-prep entry-utility-prep-cat-links">Posted in</span> My Blog | Comments Off on HOW TO USE AN ESPRESSO MAKER?

How to clip in spd pedals?

It takes practice to be able to clip into and out of pedals like SPDs that don’t have a heel or toe clip. It’s also a very important skill. How to clip into and out of SPD pedals is very important for many different types of riding.

Suppose you want to get off your bike to avoid a crash. When you’re riding a berm at high speed and need to put your leg out to get back on your feet. Or at a stop sign. Or when coming to a stop for whatever reason.

In this post, you’ll learn how to use clipless bike pedals. The process is the same whether you’re a mountain biker, a road biker, or are riding a spin bike. A summary and some videos are on this page:

If you have SPD pedals, slide the front part of your cleat-equipped bicycle shoe. When you feel the cleat getting stuck in the pedal, shift your weight to the heel until the back of the cleat gets stuck. There, the cleat should click into place.

Turn your heel outward to get off the bike.

 

Learn how to ride a stationary bike.

It’s true that it can be hard to get used to riding your bike with clipless pedals. Somewhere at the back of your mind, there’s always the knowing that you’ll fall if and when unclipping fails. Let me say this: You’ll fall. It’s a lie if someone says they can ride clipless after the first time and haven’t eaten anything bad since.

 

So, set your bike up on a trainer so you can work on your skills, then. Or, you could do it in a place with walls, like your garage. The counter in your kitchen should also be cleaned. It doesn’t even have to be in front of a truck or a tree for you to practice. As you learn how to clip in and out of your SPD pedals, you need something to stand on.

 

How to clip into your SPD pedals.

If you have a trainer, you can put your bike in it to keep it steady as you work on it. I think this is the best way to learn, but if you don’t have a trainer, don’t worry. Practice next to a wall, so you can use it as a support while you learn how to do things on your own

 

When you learn how to clip in and unclip, there are three steps:

  1. Place your bike in a trainer or stand next to a stable surface like a wall.
  2. Slide your toe forward until the front of your cycling shoe’s cleat gets stuck in the pedal, and then slide your toe back.
  3. Shift your weight toward your heel while putting down pressure on the back of the cleat until it gets stuck.

 

It’s time to get on your bike.

 

Now, get on your bike and hold on to the wall or whatever else you’re using to keep yourself steady. Ready to start? To do this, slide your toe toward the front part of the pedal, and keep it there.

 

When the cleat on your SPD pedal catches, keep sliding your foot toward the front lip until your foot gets stuck. You’ll be able to tell when the cleat hits, and there’s no need for an explanation.

 

If you want to kick a ball, start with your dominant foot, the one you use most. Why? Why do you start with your stronger leg? That gives you the momentum and stability you need as you clip in with your weaker foot.

 

Shift Your Weight to the Heel

To do this, move some of your weight to your heel. This is the next step. Make sure you push down on the pedal with your body weight until you hear a distinct click. There is no more work to do. Simple, right?

 

But don’t worry if your foot keeps moving forward. When it comes to learning how to clip into SPD clipless pedals, practice is the best way to get better. I had a hard time at first, but I was able to figure out where my cleat got stuck in the pedal and became fully engaged.

 

Make sure you do the same thing with the other leg after the one that worked well.

In this case, you should clip in with your non-dominant foot.

Congrats! You did a good job of securing yourself to the wall. It’s time to cut.

When you push off against the ground with your dominant leg, you’re now doing it. As that pedal turns around in the clockwise direction, the other pedal starts to rise back up again, too.

At 12 o’clock, step on the pedal with your other foot. This is a little different than how you did it with your stronger foot.

So, slide your toe forward so that the front of the shoe’s cleat hooks into the pedal at the front. Push down on the pedal once that happens, and then you can go faster. That downward movement should automatically make your cleats work, and that’s about all there is to it.

 Why Ride Your Bike Caught in

Beginners have a hard time using SPD pedals or any other pedals that don’t have a clip on them. Even after you learn how to clip in and out of these pedals, you can still fall over. So, why bother with pedals that are hard to use when you could just use flat-platform pedals?

 

Finally, last word.

Clipless pedals aren’t easy to use for people who are new to riding. At least six good reasons exist to stop using flat pedals and start using clipless pedals.

Then, get on your bike and stay close to a wall or countertop, or set your bike up in a trainer, so you don’t fall off. To learn how to clip in and out of your pedals, you should then learn how to do this.

You’ll have a hard time at first. If you go for a few rides, you’ll love how small and powerful your pedal strokes feel.

<span class="entry-utility-prep entry-utility-prep-cat-links">Posted in</span> My Blog | Comments Off on How to clip in spd pedals?

How to clean a skateboard deck?

Skateboards and Decks Cleaning

Dirt or mud on your skateboard deck may reduce resistance and make it difficult to do tricks. Basically, a filthy skateboard may spoil your game. It’s possible that muddy feet might cause the grip tape to slip. Dirty skateboards perform poorly. You can’t alter your performance if you don’t know how to clean your board.

Don’t worry, I’ll show you the finest DIY and home cures for cleaning your skateboard and decks. So, don’t worry about enhancing performance or keeping your skateboard clean, and save money.

Deck Cleaning using Soft Brush Wire:

This is the simplest method of cleaning your skateboard deck. You will save money and get a clean skateboard deck. This requires a soft wire brush and a Grip gum.

Step 1: Get a Soft Wire Brush

The soft wire brush may be purchased locally, but be aware that the bristles will not shred the grip tape. The brush’s bristles must be short to clean your deck’s grip tape precisely. Buying huge bristle brushes can ruin your skateboard deck’s grip tape.

Step 2: Brush the Grip Tape

Start brushing the grip’s tap using the wire brush after purchasing the soft brush. This must be done from one end of the deck to the other, section by section. This method cleans deep dirt from the deck’s surface. Also, sweep it with your hands. But careful not to force the brush or it may rip. Also, avoid stripping your board’s grit.

Step 3: Grip Gum Excess Dirt

You may get the grip gum for skateboards at a local skate store. After cleaning with the soft wire brush, apply this grip gum to clean the deck. Rub it with grip tape, then gently brush it. Reverse the procedure to receive a fresh deck. Brushing the deck gently is advised.

Cleaning your Skateboard Deck with Some Common Materials that You Find In Your Home:

If you don’t want to spend money on deck cleaning, I believe this is the best method to accomplish it.

This technique requires a firm toothbrush/soft wire brush, water, soap, grip gum (optional), bowl, and dry towel.

Step 1: Gather All Project Materials

You can quickly clean your skateboard deck or grip tape using the aforementioned items. Find an old toothbrush, a soft wire brush, soap, gum, a dry and clean towel, and water in the garage. If you have all the supplies available, you may start cleaning.

Step 2: Fill the Bowl with a Mixture of Soap and Water

Fill a medium-sized bowl with tap water and soap. Remember not to immerse your skateboard deck in water. It will destroy the skateboard’s snap or pop. You may also add lemon juice for a fresh scent, although it is optional.

Step 3: Dip And Scrub

It would help if you began cleaning at the end. Some dirtier sections need more time to remove. If your brush becomes filthy when washing the deck, rinse it back into the cleaning solution bowl and then clean the deck again. Like I stated earlier, don’t let the board touch water for too long. Also, cleaning too hard can damage the grip tap.

Step 4: Dry it with a Dry Cloth

Dry your deck after washing it with the cleaning solution and a brush. Your deck will benefit from a microfiber cloth. Place the towel over the deck and pat it dry. Fold and press the towel again until the deck dries. The wood and the bottom will also dry. Using paper towels for drying can generate more bulk and breakage.

Step 5: Drying Time

First, dry the board for 3 hours in an open place. After washing, let the board dry completely before riding it if it is safe for your skateboard.

Step 6: Clean Up Excess Dirt Grip Gum

If you have grip gum, you may rub it over the board; this is optional. Grip gum is pricey, so use a cheap rubber cement eraser instead. It’s near the hardware shop and works.

Dirty skateboards reduce performance intensity. If you want your skateboard to perform as it used to, follow the procedures below.

 

Clean Skateboard Bearing

You can do it all outside your house. If your bearing becomes filthy, you’ll need lubrication, a towel, single-use cups, and speed cream. To maximize cleaning efficiency, roll the bearing before cleaning and run it after cleaning. Added baring and removal shields. Place the towel on the work area to avoid lube-related injuries. 

 

For doing this cleaning process, you have to do the following things:

Pour or spray the lubricant into a cup first. Then pour the bearing into the cup and let it settle in the lubrication. They can be kept for an hour. If the lubricant in the cup becomes dirty, replace it with a new pure. Repeat for your eight bearings. Rep until you observe a clean and fresh bearing into the cup. Now it’s time to wipe it with the paper towel. Don’t mix them together; clean one after the other for best results. Shake the bearing to remove the excess. Finally, apply speed cream with Teflon to finish them up.

SKATEBOARD WHEELS CLEANING

Your wheels will eventually become filthy. When the wheels get yellow, you know they need cleaning. You may edit it but not reuse it. You can clean it with a moist cloth, but it doesn’t work better.

Remove the wheels first using a wrench. I need to clean the bearings. Separate them using a screwdriver. Then clean them carefully with a toothbrush or wire brush and dish soap. Brushes with narrow bristles can swiftly clean within curves and edges. Then soak them in warm water for 15-20 minutes and scrub them. Lotion helps the wheels move better. Finally, dry them with a paper towel.

SKATEBOARD GRIP TAPE CLEANING

This DIY method allows you to bike again without buying new grip tape. This requires microfiber cloths, a ribber, and a soft brush. You need enough pressure to cleanly glide it across the deck. You may use a soft dry brush and then a soft towel to remove the dust. Using a damp one and cleaning it with water may harm and degrade the grip tape. To clean the grip tap, use a soft brist

Another way to clean grip tape exists. Clean the windows with the window cleaner and delicate brushes. Repeated strokes may clean your skateboard’s grip tape till you reach the other side. Then dry it with the microfiber towels. Then use the grip gum technique to clean completely. It only works on dry grip tape, not moist grip tape.

SKATER TRUCK CLEANING TIPS

Clean the skateboard trucks with white vinegar and a paper towel. After removing the skateboard’s trucks, you can see the rust. Rust may cause truck breakdown. Wipe vinegar on the dust and rust to remove it. After a few hours, clean and massage it, then dry it with a paper towel. Spray lubricant on them to stop corrosion.

So, I hope you learned a lot about cleaning your skateboard from this post. All the approaches are simple and will assist you a lot. But remember, don’t use DIY methods unless you’ve done them right. 

 

<span class="entry-utility-prep entry-utility-prep-cat-links">Posted in</span> My Blog | Comments Off on How to clean a skateboard deck?

How To Hide Speaker Wires For Surround Sound

If you want to put surround sound in your house, this is a great idea. Not only is the sound quality of surround sound amazing, but it also makes you feel like you’re in the movie or TV show. From the comfort of your own home, you can feel like you’re going to see the movie.

A lot of people don’t like having surround sound because of all the wires. If you set up a surround sound system in your living room, you’ll be left with wires all over the place.

Make sure there aren’t a lot of wires all over the walls. There are a lot of easy ways to hide them, though. You won’t have to worry about any wires getting in the way, or them being a risk.

In this article, we have talked about a few different ways to hide the wires so that they don’t stand out. We hope you can find a way to hide the wires. Cable management is both more satisfying and safer than leaving the wires loose.

A cable clip is the first thing you can use to keep your wires together. These are cheap and very easy to use and set up. When it comes to cable clips, most of them come with self-adhesive, which is great.

This means that you don’t have to drill the clips into the wall to keep them in place, which makes them useful if you live in a rental home.

You can use as many or as few cable clips as you want because they are small. If you want to buy ones that can be nailed to the wall, this is also possible and is the best way to keep them there for a long time.

Remove the clips and make sure the self-adhesive doesn’t peel off the paint on the walls when you do. As a result, the wires are still visible, which can be an issue for people who don’t want them to be visible.

Cable 

Concealer is a concealer that is made of cable.

Our favorite way to hide wires is to use a cable concealer. These are great options, especially if you have white walls and want all of the wires to be hidden. These cable hiders hold the wires and blend in with the wall.

As they are placed on the wall, they don’t stand out as much and look a lot better than hanging wires. They are safe to use and not very expensive to buy. Because surround sound speakers have a lot of wires, you may need to buy more than one pack.

Hiding inside the walls

The best way to hide the wires is to hide them inside the walls. This is probably the cleanest and most efficient way. Even so, it’s also the most expensive choice. In order to do this, you may need to pay a professional to make sure that the wire is going through the wall correctly.

 

These two methods will both involve drilling holes into the wall and are more long-term than the first one. This is why you need to be sure where the surround sound speakers are going to be before you make a final choice.

If you want to use surround sound speakers for a long time, this is the best way to keep them in order.

Wire Tape

Speaker wire tape is similar to using cable concealer, but it costs a little less to buy. The tape makes it easy to stick the wire to the wall, and most of it can also be painted over. This makes the tape blend in with the wall so that it doesn’t stand out.

This is a good choice because it is sticky, but if you ever want to remove the tape, the chances are that the paint on the wall will come with it. Even though this isn’t a big deal, it’s important to think about, especially if you live in a rented home.

 

Decorations

If you want to hide the wires on a budget, you can use what you already have. Some of the wires can be hidden with things like curtains, plant pots, and decorations. This will not hide them completely, but it is a quick and easy way to get rid of them.

 

Wired Speakers

Over the last two decades, technology has made huge leaps and bounds. Most electrical items now have wireless options. If you don’t like having wires in your walls, but you don’t like having wires in your walls, you can try wireless speaker instead.

In comparison to other surround sound speakers, these tend to be a little more pricey. In other words: They might be good to think about. They have a lot of connections, but they will need to be charged often to stay connected.

There is nothing worse than someone leaving half way through a film, when it’s getting interesting.

Light Strips.

In a room with light strips, you can move the wires so they are near this. If you want to hide wires from view as much as possible, you’ll need to cover them up. Use tape to hide the wires and keep them in place.

 

Summary

We hope that this article has been helpful to you, and we thank you for reading it. As you can see, there are so many ways to hide the speakers from your surround sound in white. It’s not hard to do any of these things.

Even though, if you want to put the wires into the walls, we’d rather you hire a pro. Most of the time, these options aren’t too pricey, and they do a good job of keeping the wires neat and hidden.

<span class="entry-utility-prep entry-utility-prep-cat-links">Posted in</span> My Blog | Comments Off on How To Hide Speaker Wires For Surround Sound

How to slow down and stop on a skateboard

How to slow down and stop on a skateboard

With a skateboard, you can go quite fast.

As a result, it is critical to know how to slow or even halt it before a catastrophe occurs.

When learning to skateboard for the first time, finding one’s balance on the deck and pushing off are two of the first lessons beginners acquire.

Some people become overconfident and incapable of dealing with life’s unexpected twists when they finally get it.

On a steep mountain road, a longboard skateboard may achieve 90 mph (145 kph).

In the hands of someone who doesn’t know how to stop it in time, it might be a lethal weapon.

When first starting out in the sport, mastering how to properly apply the brakes on a skateboard should be a top focus.

It is possible to slow down and stop a skateboard in numerous ways.

On level land and windy days, you don’t absolutely need a steep mountain or street to ride too fast and get wounded, so keep that in mind.

The Most Popular Braking Technique

Learn the back-foot deceleration technique, which is the most important skateboard braking technique for beginners.

Here’s how it’s done:

  1. Find a medium to large-sized hill;
  2. Begin going down the road or street;
  3. Slightly lower your riding stance;
  4. Take your back foot off your board and skid it alongside the ground, leaving your lead foot on the front;
  5. Add extra pressure to your back-foot for quicker stops;

Remember to use your front foot to help balance and guide where the board is going.

Skateboarding’s basic braking technique necessitates practice and should be done while wearing a helmet.

The good news is that once you’ve finished, dragging your foot around wherever you go will be a piece of cake.

Power slides are an option if you’ve mastered riding down hills and slowing down your board.

With this braking method, you’ll wear down the soles of your shoes very quickly.

If you feel uncomfortable when skating, get off the board immediately before you reach an unmanageable speed.

The Frontside Powerslide

The frontside powerslide is an essential skill to master as you gain skating experience.

As a bonus, it’s not going to destroy your shoes or your deck.

This method of slowing down a fast skateboard does mean that your wheels will get smaller over time.

This is done by reversing the board’s orientation from vertical to horizontal.

Performing the frontside powerslide is easy if you know how:

1.To prepare for a slide, bend your knees and lower your body.

2.Apply pressure on your toes while keeping your rear foot on the tail of the board.

3.It’s important to keep your front foot in a neutral position, with your weight evenly distributed across the entire sole.

4.You should keep your body in the middle of the skateboard at all times.

5.Using the front foot as a turning axis, apply pressure to the front foot.

6.With your back foot’s toe, push the tail of the board forward on the board.

7.Keep your head above the surface to avoid losing your footing.

Remember that if you put too much weight on the front of the skateboard, it can suddenly come to a halt.

On a downhill, never attempt a first-time frontside powerslide.

It’s best to practice it on level, smooth surfaces.

The Scraping Techniques

Skateboards can be slowed down and eventually stopped using a variety of scraping techniques.

The tail of the board, the heel of your back foot, or a combination of the two can be used to enhance friction and drag and slow down your progress.

While the bluntslide is a more sophisticated mix of a power slide and a tail scrape, it will require you to learn each maneuver independently before attempting it.

 

<span class="entry-utility-prep entry-utility-prep-cat-links">Posted in</span> My Blog | Comments Off on How to slow down and stop on a skateboard

How to bridge amplifier channels on G4 series home theater amplifiers.

How to bridge amplifier channels on G4 series home theater amplifiers.

Amplifiers from AudioControl, such as the Savoy G4, Pantages G4, and Avalon G4, have the capacity of connecting multiple amplifier channels together in order to send additional power to your speakers.

It is possible to bridge amplifier channels, which means that you can merge two stereo input channels into a single mono output channel.

In a two-channel audio system or home theater, bridging output channels provides more power to huge full-range speakers that consume a lot of power, as well as more power to larger passive in-room or in-wall subwoofers.

On the AudioControl G4 series amplifiers, the following channels are capable of being bridged:

Channels on the Savoy G4

1-2 and 6-7 are two of the most common.

Channels 1-2 and 4-5 on Pantages G4 are available.

Avalon G4 – channels 1-2, 3-4, and 5-6.

IMPORTANT NOTE

When connecting the G4 series amplifiers together, do not use a speaker with an impedance of less than 8 ohm.

Once amplifier channels have been bridged, each channel of the bridged pair “sees” one-half of the total amount of speaker load.

A bridged amplifier driving an 8-ohm speaker is actually running into a 4-ohm load, as shown in the diagram.

Additionally, ensure that your speakers are rated to withstand the higher power that is delivered by linking the two networks together.

All G4 series amplifiers have the identical power output specs, which are as follows:

The power output is 230 watts per channel at 8 ohms in stereo, 300 watts per channel at 4 ohms in stereo, and 600 Watts at 8 ohms in bridged mode.

To bridge amplifier channels, for example, on a Pantages G4 amplifier, connect the positive (+) lead of your speaker cable to the positive (+) binding post of channel 1 and the negative (-) lead of your speaker cable to the negative (-) binding post of channel 2, as shown in the diagram.

When bridging, there are indications between the binding posts that indicate which connections should be utilized.

Press the Stereo/Mono button after connecting your speaker cables for bridging to turn the channel inputs into a mono mix.

When operating in mono mode, only one balanced or unbalanced input is required.

In the case of bridging channels 1-2, just the channel 1 input is used in the example.

NOTE

This four channel amplifier can be bridged down to a two channel amplifier that delivers 600 watts per channel @ 8 ohms, and it also has high pass and low pass crossovers (that can be disabled) that allow you to set up a 2.1 channel system in which channels 1-2 are powering stereo speakers and channels 3-4 are bridged to a single mono channel that is used to power a passive subwoofer speaker.

For further information on the G4 amplifiers, please see the individual product pages on the AudioControl website, which may be accessed by clicking here.

In the event that you require further assistance, please contact us.

Support is available from 8 a.m. to 5 p.m. pacific standard time Monday through Friday.

 

<span class="entry-utility-prep entry-utility-prep-cat-links">Posted in</span> My Blog | Comments Off on How to bridge amplifier channels on G4 series home theater amplifiers.